====== Setting Up The Cricket A600 Broadband Modem ====== ===== Introduction ===== First thing you need to do is download wvdial and all it's dependencies. It will do that automatically. From terminal as root: # tazpkg get-install wvdial Download this:[[http://people.slitaz.org/~jozee/packages/3G_modem/usb_modeswitch-1.0.5.tazpkg|Jozee's USB_Modeswitch]] Then from terminal as root install it: # tazpkg install /path/to/usb_modeswitch-1.0.5.tazpkg /path/to is where you downloaded it to. So you will need to adjust the above. Make a script called flipflop.sh You can place it anywhere but I am going to use where I have it as an example: ///home/tux/scripts/// If you use another name besides "tux" then adjust it accordingly. Now open up flipflop.sh with your prefered editor. Put the following in it and save the file: /usr/sbin/usb_modeswitch sleep 15 usb_modeswitch -v 0x1f28 -p 0x0020 -R 1 From terminal we need to chmod it so you can use the script: # chmod a+x /home/tux/scripts/flipflop.sh Again if you have it saved somewhere else then adjust accordingly. Sorry to repeat that lol. ===== wvdial.conf ===== We have now installed all that we need to install. There are just a few more steps involved. We need to edit wvdial.conf . As root from terminal enter this: # leafpad /etc/wvdial.conf In wvdial.conf we need to make it look like this: [Dialer Defaults] Modem = /dev/ttyACM0 Baud = 460800 Stupid Mode = 1 Auto DNS = 1 Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ISDN = 0 Modem Type = USB Modem Phone = #777 FlowControl = Hardware (CRTSCTS) Dial Command = ATDT Username = Your Cricket Number Goes Here. Password = Cricket Where it says "Your Cricket Number Goes Here" replace that with your cricket number. Your cricket number should be on your monthly bill if you don't know what it is. Once it is done save the file. Now again as root in terminal issue this command: # /home/tux/scripts/flipflop.sh You should get something like this below: Looking for target devices ... No devices in target mode or class found Looking for default devices ... Found default devices (1) Found a default device NOT in target class mode Accessing device 003 on bus 002 ... Using endpoints 0x08 (out) and 0x87 (in) Inquiring device details; driver will be detached ... Looking for active driver ... OK, driver found ("dummy") OK, driver "dummy" detached Received inquiry data (detailed identification) ------------------------- Vendor String: Cricket Model String: T-Flash Disk Revision String: 2.31 ------------------------- Device description data (identification) ------------------------- Manufacturer: Cal-comp E&CC Limited Product: USB Micro SD Storage Serial No.: XXXXXXXXXXXXXXX ------------------------- Setting up communication with interface 0 ... Trying to send the message to endpoint 0x08 ... OK, message successfully sent Device is gone, skipping any further commands -> Run lsusb to note any changes. Bye. Looking for target devices ... No devices in target mode or class found Looking for default devices ... No default device found. Is it connected? Bye. tux@slitaz:~$ It looks like it totally failed but it didn't. It just doesn't know what the driver is. Again from root execute this command: # modprobe cdc_acm That should be the last time you have to enter that command. We will now add it to to the LOAD_MODULES line in /etc/rcS.conf to load at boot. ===== rcS.conf ===== From terminal as root: # leafpad /etc/rcS.conf Go down to the following line: LOAD_MODULES="snd_intel8x0 yenta_socket rtc agpgart intel-agp" Add this to the line: "cdc_acm" It should now look like this: LOAD_MODULES="snd_intel8x0 yenta_socket rtc cdc_acm agpgart intel-agp" Save it and exit. We are almost done. From terminal as root again give this command: # wvdial It should now dial and connect. Do not close the terminal or it will disconnect. Everytime you poweroff or unplug the modem you have to do the flipflop.sh like I showed you above. If you just reboot your computer you don't have to do the flipflop.sh. Good Luck